Iron gates
Custom iron gates control access, add curb appeal, and are built to last. We fabricate driveway gates, pedestrian gates, and decorative entry gates in steel or wrought iron, with manual or automatic operation.
What's included
- Measurement and design consultation
- Custom gate fabrication
- Post or pillar installation if needed
- Gate hanging and hardware installation
- Powder-coat finish
- Optional electric operator and intercom wiring
Typical price
Ballpark installed prices for 2026, for planning only. We confirm the exact price in a written quote after we measure.
Get your priceAbout iron gates
Iron gates fall into two broad groups. Pedestrian gates are single walk-through gates for a front walk, side yard, or garden, usually styled to go with an existing fence. Driveway gates are wider single or double gates that either swing or slide, and they are often automated. Styles run from simple flat-top picket gates to arched tops, scrollwork, and privacy designs with solid or perforated panels.
A gate is a moving load, so the posts and hinges matter as much as the gate itself. Our team sizes the posts or pillars for the gate's weight and width, sets them in footings below the frost line, and chooses hinges, latches, and stops that keep the gate from sagging. On driveways, the slope, snowbanks, and plow paths all affect whether a swing or a slide gate makes more sense.
If you want automation, decide up front. An operator changes the post size, the footing, and the conduit and wiring that run to it, and it adds safety devices like photo eyes and edge sensors. Retrofitting a motor onto a gate that wasn't built for one is usually more expensive and less reliable.
How the project works
Share the project
Send the opening width, a few photos, and whether you want manual or automatic operation. We review it and set up a site visit.
Site visit
Our crew measures the opening, checks the grade across the driveway, swing or slide clearance, existing posts or pillars, and whether power is available nearby.
Design and quote
You choose the style, configuration, and hardware; we quote the job and note any permit or electrical work.
Fabrication and finish
The gate and posts are fabricated and finished, usually galvanized, powder-coated, or both, and the hardware is fitted.
Install and setup
Posts are set, the gate is hung and adjusted, and any operator, safety sensors, keypad, or intercom are installed and tested, with electrical connections made by a licensed electrician where required.
Materials and finishes
Steel gates
Welded steel is the standard for custom iron gates. It is strong enough for wide driveway spans and takes almost any design, but it's heavy, which drives the post and hinge sizing.
Galvanizing and powder coat
The bottom rail of a gate sits in snow, slush, and salt spray all winter. Galvanizing under powder coat gives the best protection there; powder coat alone over well-prepped steel works but needs chips touched up quickly.
Aluminum gates
Lighter and rust-free, which is easier on hinges and operators. A good fit for wide decorative gates where security is less of a concern; less rigid than steel and more easily damaged by an impact.
Hardware
Heavy-duty adjustable hinges, gravity or magnetic latches, drop rods for double gates, and galvanized or stainless fasteners. Hardware is the part of a gate that wears, so it is worth choosing well.
Massachusetts code and permits
Gates generally fall under the same local rules as fences: your town sets height, setback, and permit requirements, and some towns also regulate how close a driveway gate can sit to the street. Automatic gates add electrical work, which needs a licensed electrician and usually an electrical permit, and gate operators are expected to meet the UL 325 safety standard, with entrapment protection such as photo eyes or edge sensors. Gates that are part of a pool barrier must be self-closing and self-latching. Your local building department has the final say on what your gate needs.
What affects the price
- Opening width and gate height
- Single vs. double gate, and swing vs. slide
- Design complexity and any privacy panels
- New posts or pillars vs. hanging on existing ones
- Hardware grade: hinges, latches, drop rods, locks
- Automation: operator type, safety sensors, access controls, and the power run
- Finish: powder coat vs. galvanizing plus powder coat
Common questions
- Can I get an automatic gate?
- Yes — our crew installs gate operators for both swing and sliding gates, and can coordinate intercom or keypad access systems.
- How wide can a driveway gate be?
- We fabricate single and double gates to fit your driveway opening. Double gates handle wider openings; the right configuration depends on your driveway layout and swing clearance.
- How long does a gate project take?
- Most gate projects are quoted, fabricated, and installed within a few weeks. Automatic gate installs take a bit longer to coordinate the electrical work.
- Do you install gates on existing pillars or posts?
- Yes — if your posts or pillars are in good condition, our crew can hang a new gate on them. We'll assess them during the site visit.
- Swing gate or sliding gate — which is better for a Massachusetts driveway?
- A swing gate is simpler and is usually the default when there's clear, fairly level space for the leaves to open; a sliding gate is better when the driveway slopes up behind the gate, space is tight, or the opening is very wide. A sliding gate needs a clear run alongside the opening, which has to be kept free of snow in winter. Our team recommends a layout after seeing the driveway.
- Do automatic gates work in snow and ice?
- Yes, if they're set up for it. Swing gates need their swing path cleared, sliding gates need their track or rollers kept clear, and operators suited to cold weather perform more reliably. Our team can recommend an operator and layout that fit winter use.
- Do I need a permit for a driveway gate in Massachusetts?
- It depends on your town. Fence and gate rules, including height, setback, and whether a permit is needed, are set locally, and an automatic gate usually also needs an electrical permit. Our team checks with your local building department before fabrication.
- Why do iron gates sag, and how is it prevented?
- Gates usually sag because the hinge post is undersized, its footing has heaved, or the gate frame isn't braced. Prevention is a properly sized post on a footing below the frost line, a rigid welded or braced frame, and heavy-duty adjustable hinges. Our crew can often fix an existing sagging gate by resetting the post or re-hanging the gate.

